Release T1

[pannal]

p3i T1

This is the initial release of p3i, directly based off of U3k B11, with a lot of improvements, most notably:

UI rendering improvements

I was able to discover a whole bunch of performance issues within the guilib code of Kodi, many of them existed for years, or even decades. Changes have been made to specific compositing, message queueing, as well as efficiency across a wide range of GUI controls.

All in all, the guilib changes result in:

• faster UI rendering (especially complex UIs, such as PM4K and skins)
• more efficient invalidation of controls across the board
• less CPU usage during transitions and texture loading
• significantly less CPU usage when idle while showing certain types of UIs

This can be very roughly summarized as (vs. other builds/stock Kodi):

  ┌─────────────────────────────────────────┬───────────────────────────────────────────────┐
  │                Scenario                 │             Estimated Improvement             │
  ├─────────────────────────────────────────┼───────────────────────────────────────────────┤
  │ Idle with scrollbar visible             │ 60-80% reduction in GUI CPU usage             │
  ├─────────────────────────────────────────┼───────────────────────────────────────────────┤
  │ Idle with images/buttons (no scrollbar) │ 30-50% reduction in GUI CPU usage             │
  ├─────────────────────────────────────────┼───────────────────────────────────────────────┤
  │ Active scrolling                        │ 20-40% reduction in per-frame processing      │
  ├─────────────────────────────────────────┼───────────────────────────────────────────────┤
  │ Image cross-fade transitions            │ ~80% reduction in dirty region overhead       │
  ├─────────────────────────────────────────┼───────────────────────────────────────────────┤
  │ Complex UIs with many controls          │ 30-50% reduction due to message deduplication │
  └─────────────────────────────────────────┴───────────────────────────────────────────────┘

Those fixes will be pull requested towards Kodi upstream, so everybody can benefit.

There's more to be done here, this "just" fixes the most obvious ones.

Other notable changes

• "Low latency audio mode" backported from Kodi 22 (via thexai and subsequent commits/PRs)
  This adds a new setting under System/Audio called "Low latency mode", enabled by default. It significantly reduces the time audio streams take to "resume" when playback is resumed, vs. the video stream. If you encounter any issues, try disabling this first.

• Fixed BT/Wi-Fi pairing in the "CoreELEC Settings"-Addon
  Since U3k B9's Python upgrade, BT and Wi-Fi pairing stopped working. Due to a very old dbus library used by that addon, which isn't supported anymore and doesn't work with Python 3.13, I decided to rewrite a big part of it to utilize the newer dbussy/ravel library. This also reduces the time it takes to actually reboot when hitting the "Reboot" option in the exit menu.

• VideoPlayer: Fix seeking to resume point with LAV filters
  This fixes the issue where seeking to a resume point would incorrectly
  jump back to position 0 when LAV Full mode is active.

  Based on commit 7d47c17 from avdvplus/xbmc (cpm-code).

• VideoPlayer: Sync to later start time to fix AV desync
  This prevents AV desync that can occur when video starts later than
  audio, particularly noticeable with LAV filter chain.

  Based on commit 31c65c3 from avdvplus/xbmc (cpm-code).

VC-1 fixes have not been included in this release, as we've found last-minute compatibility issues. Expect them in T2.

LAV Filters & PM4K

As with U3k B11, LAV filters are included as an option for fixing audio issues (under Settings/System/CoreELEC, bottom). By default this is set to Off, as during testing these fixes weren't necessary (anymore). If you tend to watch seamless branching titles, you can set this to "LAV SB". If you're a user of the latest PM4K beta, the addon will take care of automatically enabling LAV SB for affected seamless branching titles, so you can leave this at Off. "LAV Full" isn't necessary or recommended, but can be beneficial in certain scenarios, and should be fully compatible with PM4K's Alternate Seek functionality.

Installation

1. Dirty

Drop the update tar into your CoreELEC update folder and reboot - this can be used as a dirty upgrade from CPM A14 or any of the U3k builds. Resetting Settings/System/CoreELEC to defaults after doing this could be beneficial but hasn't proven necessary.

2. Flash

Use the provided Flash img.gz to prepare your SD card as you would with any other CoreELEC build.

advancedsettings.xml

If you'd like, you can add the following to your advancedsettings.xml, which further improves UI rendering, but is not strictly necessary:

<gui>
    <fronttobackrendering>true</fronttobackrendering>
    <geometryclear>false</geometryclear>
  </gui>

Thanks

A massive shoutout to everyone involved in this build!

Full Changelog (Kodi core): https://github.com/pannal/xbmc/commits/T1
Full Changelog (CoreELEC-Settings): https://github.com/pannal/service.coreelec.settings/commits/T1

---

This discussion was created from the release Release T1.

[pannal]

Feel free to discuss!

[Sunset-1982]

Amazing work! Looks very good so far. Looking forward for the next releases with more of these speed up tunings.

[GhostM121]

Just wondering if there is any concerns with the bluetooth stuff, I would hate for my harmony to lose connection if i try this branch, was quite a pain to set up.

[pannal]

Not really. What broke in U3k B11 is the Wi-Fi and BT pairing part of the CoreELEC Settings addon. Previously paired devices worked also in U3k B11. p3i fixes the pairing part, so we should be back to normal now.

[demouser007]

Are you planning to backport this fix for DVDs? It seems that DVDs may finally work in CoreELEC.

[pannal]

Oh wow this is a big one. That'll take some time.

[demouser007]

That would be awesome! Right now, the only thing stopping S922X-based devices from being perfect is non-working DVDs.

[pannal]

@demouser007 I'll probably try merging these changes tomorrow. Would you be up for testing a T2_dev build? You'd need to join the #ugoos-mediaplayer Discord channel (see README for link).

Otherwise I'd need very specific instructions in how to test this issue.

[demouser007]

Yes, I'm ready to test it.

[pannal]

This is not backportable to Kodi 21.3, I'm sorry.

[mrmorrison85]

avdvplus, in R6, fixed the default color space bug. In the display settings, when a specific color space or a specific bit depth is set, it was ignored after a Dolby Vision movie was played.
R6 corrected this problem. Could you implement the change in T2?

[pannal]

Yes, the fix will be in T2. It's already dissected from the huge R* blob commits avdvplus does and applied properly: pannal/xbmc@02cf90d

[andruhin64]

Please maintain the ability to view 3D.iso files. Everything works fine in the T1 version for now. 3D doesn't work with AVDV.